Putting a swing on your porch or deck will definitely add elegance to it. Not only that, but family and friends will be able to enjoy your porch more when you install a swing, because after all, a porch or deck with a swing in it is a lot more interesting than a bare one. Having a swing, your porch or deck will instantly become a favorite gathering place. If you think installing a swing in your porch or deck is difficult, think again. Adding a swing to your porch or deck can be a breeze if you follow the step by step instructions below. 1. The right swing must be placed properly in the place. The first thing you should do before buying a swing set is to measure the height of your porch or the a place in the garden for the chains used for support and the width to ensure crash and bump free swinging. 2. Purchase a hanging kit along with the swing. Ensure that it has all the necessary galvanized items and chain for heavy-duty purposes that you will need for the particular swing that you bought. Read the directions well when you are buying your hanging kit. Ensure you have all the necessary tools, and if not, prepare a list of items you will need and make a trip to the hardware store. 3. Look for an overhead beam with an 8-foot clearance under it in your porch or deck. This is where you will install the two hooks for the swing that should be given space the width of the swing to support the chains. To prevent the splitting of the wood upon screwing in the big hooks that are useful in holding the swing safely, drill pilot holes first. 4. Choose a swing set that requires minimal assembly. First take all the parts out of the box. Find the package of nuts and bolts then set it aside. Look for the instructions booklet and read it carefully. To avoid confusion, lay out all of the parts on the ground the way they will eventually connect in the finished assembly. If there are any ground coverings or mats lay them also on the ground. Get some help holding the pieces as you assemble them or use a small bucket or tupperware container to ensure none of the smaller pieces get lost. Assembling Your Swing: 1. Look for the long poles that will form the swings frame. Connect two of the three poles at the end to form an acute angle with the nuts and bolts provided. Connect the second set of two uprights the same way. Also connect any braces included onto the uprights. The braces should attach about halfway along the uprights. 2. There are basically two types of swings, those with holes in the arms and those that come with mounted chains that are attached to the swing's lower frame. The former is easy to hang but the latter can be more comfortable to sit on. 3. Preserve your swing before hanging by using a sanding sealer under a varnish with polyurethane. Annually check for splinters and reseal if needed. 4. Look for the crosspiece which is usually the largest piece of metal or a long wooden beam. Connect this to the apex of each set of uprights making sure that any holes or hooks face the right way so that it will be possible to attach the swing correctly. 5. When everything is in its place tighten the bolts and stand the swing set on its feet. Get the chains or rope for use to hanging the swing. Using a stepladder, attach the chains to the crosspiece. Hooks should be provided with the swing set. The swing seat should be attached to the hanging chain. Measure each side so the swing hangs evenly. 6. You will need four chains to hang the swing from its hooks. The first two chains will descend from each hook, one to the front of the swing and one to the back. The chains must at least be seven feet long because it will hang from a beam that is 8 feet above. The swing must be not more than 17 inches from the ground so it is easy for individuals to get on and off. 7. For safety, all hardware must be screwed securely into the wood and chain connectors must be used. Before hanging the swing, double check that all hardware is installed. 8. Use a frame if you have any doubt that your porch can support your swing. Do not hang swings from masonry or bricks. 9. It is better if you use bolts instead of screws. 10. It is highly suggested that you drill through the support beam to put a long eye bolt through it, then secure it with a large flat washer and locking bolt. 11.Ask a friend for help or use an ironing board for support when you lift the swing and its harness near the beam. After hooking the swing in place, adjust the chains evenly then get on the swing to test it. Now you are ready to show off your new swing to your friends and family! |
Home
